interference fit
英 [ˌɪntəˈfɪərəns fɪt]
美 [ˌɪntərˈfɪrəns fɪt]
静配合；压配合；干涉配合；公盈配合
双语例句
- The Interference Fit for Centrifugal Compressor and The stress Analysis for Impeller Construction
离心压缩机过盈配合叶轮结构应力分析 - Kinetics of Oxidation of Organic Compound by Diperiodatonickelate ( IV) Ion in Alkaline Medium Spectrophotometrically; High precision simulative analysis on conical interference fit of bearing inner ring of precision grinding machine
分光光度法研究二过碘酸合镍（IV）配合物氧化有机物动力学及机理精密磨床轴承内圈圆锥过盈配合高精度仿真分析 - The study of the assembly stresses over and above field of the lame problem for interference fit construction
非拉梅问题的过盈配合结构装配应力的研究 - Tensional stresses, perhaps caused by an interference fit on the shaft, promote diameter increases.
张力过大，也许就造成轴过盈配合，促进直径增加。 - Calculation Method Research of the Interference Fit for High Speed Motorized Spindle Bearings
高速电主轴轴承配合过盈量的计算方法研究 - Clutch engagement speed test Calculation of the Interference Fit Joints at High Rotary Speed
离合器接合转速试验高速旋转状态下压配合联接的设计计算 - The washer shall be clinched to the stud end with a tight slip fit to an interference fit.
由滑动配合的相互作用力使垫片咬紧于螺栓。 - The Interference Fit Analysis of Mosaic-type Rotating Ring on Stern Shaft Mechanical Seal
船舶尾轴机械密封镶嵌式动环过盈配合分析 - Before the assembly of parts of the match, especially interference fit the size and the relevant review.
装配前应对吾爱内用抗菌乳膏零、器件的首要配合尺寸，特别是过盈配合尺寸及相关精度进行复查。 - Stress Distribution Laws of Overhanging Interference Fit between Ceramics Column and Metal Sleeve Based on FEA
基于有限元分析的金属套/陶瓷柱外伸式过盈连接应力分布规律 - The methods of interference fit analysis and their advantages were described in detail, and the basis for equipment stress analysis and the design optimization was provided.
较系统地总结过盈配合的计算方法及各方法的优缺点，为设备的应力分析及结构优化设计提供了依据。 - Interference Fit Axisymmetric Entity Finite Element Structure Analysis Program Development
过盈配合组合轴对称体结构分析有限元程序开发 - Three quenched bushes are pressed on the hollow spindle ( sleeve) with a big interference fit, thus the spindle can move forward and backward precisely within the bush.
三个大干涉配合的淬火衬套压装在空心轴（镗套）上，因此，主轴能在衬套内前后精确移动； - Application of CFD in Aero-Engine Turbomachinery Designing The Interference Fit for Centrifugal Compressor and The stress Analysis for Impeller Construction
计算流体力学在航空叶轮机设计中的应用离心压缩机过盈配合叶轮结构应力分析 - The control rod drive mechanism ( CRDM) housing of nuclear power plant is installed on the reactor pressure vessel head by welding and interference fit.
核电站主设备控制棒驱动机构管座是通过焊接和过盈配合共同作用安装在压力容器顶盖上。 - The planet gear shafts and the axis holes of the planet gears are connected under an interference fit.
行星齿轮轴与行星齿轮的轴孔之间为过盈配合。 - Study on Contact Characteristics of Interference Fit based on FEM
基于有限元法的过盈配合接触特性分析 - High precision simulative analysis on conical interference fit of bearing inner ring of precision grinding machine precision CNC internal and end grinding machine
精密磨床轴承内圈圆锥过盈配合高精度仿真分析精密数控内圆-端面磨床 - Analysis and Computation on Interference Fit of High-Speed Motor Rotor Based on Contact Nonlinear Theory
基于接触非线性理论的高速电机转子过盈配合分析计算 - Conclusion Isilicon gel coat using interference fit manner achieved device performance requirements in the conjoint condition and antifatigue.
结论采用过盈装配形式的硅胶外套在轮缘结合状况及抗疲劳度方面达到设备性能要求。 - In this paper, the design medthod of interference fit of rolling bush has been discussed, and a calculating method is put forward to work out the interference when measuring the circumference.
本文讨论了薄壁卷制衬套过盈配合的设计方法，并给出了测量时过盈度的计算方法。 - In the case of interference fit, the amount of interference has significant effect on fatigue, closeness and stress corrosion of the rivet joints.
干涉配合是改善铆接接头疲劳性能和钉孔自身密封性能的一项有效的工艺措施。 - The interference fit between the gate and seat provides bubble tight shutoff even under the lowest pressure.
即使在最低的管线压力下，闸板与阀座之间的配合也能够实现气泡级密封功能。 - Reliability and optimum design for interference fit are thoroughly analyzed, and the research results are tested and verified with an example.
对过盈联结的可靠性优化设计进行了研究，用实例验证了研究结果的正确性。 - The influence of bearing interference fit and temperature on bearing radial internal clearance are studied;
研究轴承过盈配合及温度对轴承游隙的影响； - This paper deals with designed theory and method for interference fit between plastic shaft and plastic hub.
陈述了塑料实芯轴与孔座间过盈连接的设计理论和方法。 - A detailed analysis on interference fit of hub was carried out by means of elastic mechanics and finite element method, in view of the above, the shortcomings of elastic mechanics method and the advantages of finite element method have been pointed out.
用弹性力学和有限元方法对轴毂过盈联接进行了详细的分析，据此指出了弹性力学方法的弊端和有限元方法的优势。 - But the interference fit by hydroform result in the damage occurring on the contact surface.
然而，由于锥套与辊颈利用液压胀形实现过盈装配，使得接触面间在装配过程中发生表面损伤。 - In this paper, the static an dynamic formulas are derived for calculating the interference fit and contact pressure.
文章研究了高速主轴过盈联结的特性，分别推导出了高速主轴在静态和动态条件下过盈量和接触应力的理论公式。 - The design of rotor, material selection of rotor shaft and design of interference fit between rotor and shaft have been studied in this paper. The design examples are presented and the results have met the demands for engineering practice.
对高速电磁轴承转子轴中的转子设计、转子轴材料选择和转子与轴的过盈配合设计进行了研究，并给出了设计实例，结果达到了工程设计要求。